View NCP600SN180T1G_707513.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NCP600 High Performance Low-Power, LDO Regulator with Enable
The NCP600 provides 150 mA of output current at fixed voltage options, or an adjustable output voltage from 5.0 V down to 1.250 V. It is designed for portable battery powered applications and offers high performance features such as low power operation, fast enable response time, and low dropout. The device is designed to be used with low cost ceramic capacitors and is packaged in the TSOP-5/SOT23-5.
Features http://onsemi.com
5 1 TSOP-5 SN SUFFIX CASE 483
* Output Voltage Options: * * * * * * * * * * * *
Adjustable, 1.5 V, 1.8 V, 2.8 V, 3.0 V, 3.3 V, 5.0 V Ultra-Low Dropout Voltage of 150 mV at 150 mA Adjustable Output by External Resistors from 5.0 V down to 1.250 V Fast Enable Turn-on Time of 15 ms Wide Supply Voltage Range Operating Range Excellent Line and Load Regulation High Accuracy up to 1.5% Output Voltage Tolerance over All Operating Conditions Typical Noise Voltage of 50 mVrms without a Bypass Capacitor Pb-Free Package is Available
MARKING DIAGRAM
5 xxx AYWG G 1 xxx A Y W G = Specific Device Code = Assembly Location = Year = Work Week = Pb-Free Package
Typical Applications
(Note: Microdot may be in either location)
SMPS Post-Regulation Hand-held Instrumentation Noise Sensitive Circuits - VCO, RF Stages, etc. Camcorders and Cameras
PIN CONNECTIONS
Vin GND 1 2 3 (Top View) * ADJ - Adjustable Version * NC - Fixed Voltage Version 4 ADJ/NC* 5 Vout
VIN Fixed Voltage Only Driver w/ Current Limit GND Thermal Shutdown + -
VOUT
ENABLE
+ 1.25 V -
ORDERING INFORMATION
ADJ Adjustable Version Only ENABLE
See detailed ordering and shipping information in the package dimensions section on page 12 of this data sheet.
Figure 1. Simplified Block Diagram
(c) Semiconductor Components Industries, LLC, 2006
1
September, 2006 - Rev. 3
Publication Order Number: NCP600/D
NCP600
PIN FUNCTION DESCRIPTION
Pin No. 1 2 3 4 5 Pin Name Vin GND ENABLE ADJ/NC Vout Positive Power Supply Input Power Supply Ground; Device Substrate The Enable Input places the device into low-power standby when pulled to logic low (< 0.4 V). Connect to Vin if the function is not used. Output Voltage Adjust Input (Adjustable Version), No Connection (Fixed Voltage Versions) (Note 1) Regulated Output Voltage Description
MAXIMUM RATINGS (Voltages are with respect to device substrate.)
Rating Voltage at Any Pin Output Short Circuit Duration (Note 2) Operating Junction Temperature Storage Temperature Symbol
-
Value -0.3 to 6.0 Infinite +150 -65 to +150
Unit V - C C
ISC TJ(MAX) Tstg
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. True no connect. Printed circuit board traces are allowable. 2. Internally protected by thermal shutdown circuitry.
ATTRIBUTES
Characteristic ESD Capability Moisture Sensitivity Package Thermal Resistance Junction-to-Ambient, RqJA Human Body Model Machine Model Value 3.5 kV 400 V MSL1/260 250 C/W
http://onsemi.com
2
NCP600
ELECTRICAL CHARACTERISTICS
(Vin = 1.750 V, Vout = 1.250 V, Cin = Cout =1.0 mF, -40C TJ 125C, Figure 2, unless otherwise specified.) (Note 3) Characteristic Symbol Test Conditions Min Typ Max Unit
Regulator Output (Adjustable Voltage Version) Output Voltage Vout Iout = 1.0 mA to 150 mA Vin = 1.75 V to 6.0 V, Vout = ADJ Iout = 1.0 mA to 150 mA f = 120 Hz f = 1.0 kHz f = 10 kHz Vin = 1.750 V to 6.0 V, Iout = 1.0 mA Iout = 1.0 mA to 150 mA f = 10 Hz to 100 kHz 1.231 (-1.5%) 1.250 1.269 (+1.5%) V
Ripple Rejection (Vin = Vout + 1.0 V + 0.5 Vp-p)
RR
dB - - - - 62 55 38 1.0 - - - 10 mV
Line Regulation
Regline Regload Vn Isc VDO
Load Regulation Output Noise Voltage Output Short Circuit Current Dropout Voltage Vout = 1.25 V Vout = 1.5 V Vout = 1.8 V Vout = 2.5 V Vout 2.8 V
- - 300
2.0 50 550 175 150 125 100 75
15 - 800 250 225 175 150 125
mV mVrms mA mV
Measured at: Vout - 2.0%, Iout = 150 mA, Figure 3
- - - - -
Regulator Output (Fixed Voltage Version) (Vin = Vout + 0.5 V, Cin = Cout =1.0 mF, -40C TJ 125C, Figure 4, unless otherwise specified.) (Note 3) Output Voltage 1.5 V Option 1.8 V Option 2.8 V Option 3.0 V Option 3.3 V Option 5.0 V Option Ripple Rejection (Vin = Vout + 1.0 V + 0.5 Vp-p) Vout Iout = 1.0 mA to 150 mA Vin = (Vout + 0.5 V) to 6.0 V V 1.470 1.764 2.744 2.940 3.234 4.900 (-2%) - - - - 1.500 1.530 1.836 2.856 3.060 3.366 5.100 (+2%) dB 62 55 38 1.0 - - - 10 mV
RR
Iout = 1.0 mA to 150 mA f = 120 Hz f = 1.0 kHz f = 10 kHz Vin = 1.750 V to 6.0 V, Iout = 1.0 mA Iout = 1.0 mA to 150 mA
Line Regulation
Regline Regload
Load Regulation 1.5 V Option 1.8 V Option 2.8 V Option 3.0 V Option 3.3 V Option 5.0 V Option Output Noise Voltage Output Short Circuit Current Dropout Voltage 1.5 V Option 1.8 V Option 2.8 V Option 3.0 V Option 3.3 V Option 5.0 V Option
mV - - - - - - - 300 2.0 2.0 2.0 2.0 2.0 2.0 50 550 150 125 75 75 75 75 20 25 30 30 30 30 - 800 225 175 125 125 125 125 mVrms mA V - - - - - -
Vn Isc VDO
f = 10 Hz to 100 kHz
Measured at: Vout - 2.0%
3. Designed to meet these characteristics over the stated voltage and temperature recommended operating ranges, though may not be 100% parametrically tested in production. 4. Guaranteed by design.
http://onsemi.com
3
NCP600
ELECTRICAL CHARACTERISTICS (Vin = 1.750 V, Vout = 1.250 V (adjustable version)), (Vin = Vout + 0.5 V (fixed version)), Cin = Cout =1.0 mF, -40C TJ 125C, Figure 2, unless otherwise specified.) (Note 5)
Characteristic General Ground Current Ground Current Adjustable Option 1.5 V Option 1.8 V Option 2.8 V Option 3.0 V Option 3.3 V Option 5.0 V Option Thermal Shutdown Temperature (Note 6) Thermal Shutdown Hysteresis ADJ Input Bias Current Chip Enable ENABLE Input Threshold Voltage Voltage Increasing, Logic High Voltage Decreasing, Logic Low Enable Input Bias Current (Note 6) Timing Output Turn On Time Adjustable Option 1.5 V Option 1.8 V Option 2.8 V Option 3.0 V Option 3.3 V Option 5.0 V Option tEN ENABLE = 0 V to Vin ms - - - - - - - 15 15 15 15 15 15 30 25 25 25 25 25 25 50 IEN Vth(EN) 0.9 - - - - 3.0 - 0.4 100 nA V ISTBY IGND ENABLE = 0 V, Vin = 6 V -40C TJ 85C ENABLE = 0.9 V, Iout = 1.0 mA to 150 mA - 0.01 1.0 mA mA - - - - - - - 150 - -0.75 100 135 140 140 140 145 145 175 10 - 135 170 175 175 175 180 180 200 - 0.75 C C mA Symbol Test Conditions Min Typ Max Unit
TSD TSH IADJ
5. Designed to meet these characteristics over the stated voltage and temperature recommended operating ranges, though may not be 100% parametrically tested in production. 6. Guaranteed by design.
http://onsemi.com
4
NCP600
VIN CIN 2 ENABLE 3 4 1 5 VOUT COUT
Figure 2. Typical Application Circuit for Vout = 1.250 V (Adjustable Version)
VIN CIN
1 2
5 R1 4 R2
VOUT COUT
ENABLE
3
Figure 3. Typical Application Circuit for Adjustable Vout
VIN CIN
1 2 3
5
VOUT COUT
4
Figure 4. Typical Application Circuit (Fixed Voltage Version)
http://onsemi.com
5
NCP600
TYPICAL CHARACTERISTICS
1.260 1.260
OUTPUT VOLTAGE (V)
Iout = 1.0 mA
OUTPUT VOLTAGE (V)
1.256
1.256 Iout = 1.0 mA 1.252
1.252 Iout = 150 mA
1.248 Vin = Vout + 0.5 V Vout = ADJ
1.248
Iout = 150 mA Vin = 6.0 V Vout = ADJ -15 10 35 60 85 110 125
1.244 1.240 -40 -20
1.244 1.240 -40
0
20
40
60
80
100
120
TEMPERATURE (C)
TEMPERATURE (C)
Figure 5. Output Voltage vs. Temperature (Vin = Vout + 0.5 V)
1.500 Vout, OUTPUT VOLTAGE (V) Iout = 1.0 mA OUTPUT VOLTAGE (V) 1.495 1.500
Figure 6. Output Voltage vs. Temperature (Vin = 6.0 V)
Iout = 1.0 mA 1.495
1.490 Iout = 150 mA
1.490 Iout = 150 mA 1.485
1.485
1.480 1.475 -40
1.480 1.475 -40
-15
10
35
60
85
110 125
-15
10
35
60
85
110 125
TEMPERATURE (C)
TEMPERATURE (C)
Figure 7. Output Voltage vs. Temperature (1.5 V Fixed Output, Vin = 2 V)
3.005 3.000 OUTPUT VOLTAGE (V) 2.995 2.990 2.985 2.980 2.975 -40 Iout = 1.0 mA OUTPUT VOLTAGE (V) 3.005 3.000 2.995 2.990 2.985 2.980 2.975 -15 10 35 60 85 110 125 2.970 -40
Figure 8. Output Voltage vs. Temperature (1.5 V Fixed Output, Vin = 6 V)
Iout = 1.0 mA
Iout = 150 mA
Iout = 150 mA
-15
10
35
60
85
110 125
TEMPERATURE (C)
TEMPERATURE (C)
Figure 9. Output Voltage vs. Temperature (3.0 V Fixed Output, Vin = 3.5 V)
Figure 10. Output Voltage vs. Temperature (3.0 V Fixed Output, Vin = 6 V)
http://onsemi.com
6
NCP600
TYPICAL CHARACTERISTICS
5.000 Iout = 1.0 mA 4.995 OUTPUT VOLTAGE (V) 4.990 Iout = 150 mA 4.985 4.980 4.975 4.970 4.965 -40 -15 10 35 60 85 110 125 OUTPUT VOLTAGE (V) 4.995 4.990 4.985 Iout = 150 mA 4.980 4.975 4.970 4.965 -40 -15 10 35 60 85 110 125 5.000 Iout = 1.0 mA
TEMPERATURE (C)
TEMPERATURE (C)
Figure 11. Output Voltage vs. Temperature (5.0 V Fixed Output, Vin = 5.5 V)
250 Vout = ADJ DROPOUT VOLTAGE (mV) 200 DROPOUT VOLTAGE (mV) Iout = 150 mA 250
Figure 12. Output Voltage vs. Temperature (5.0 V Fixed Output, Vin = 6 V)
Iout = 150 mA 200 Vout = 1.25 V 1.50 V 150 1.80 V 2.80 V 100 3.00 V 50 0 -40 -20 5.00 V
150
100 Iout = 50 mA 50 0 -40 -20 Iout = 1.0 mA 0 20 40 60 80 100 120
0
20
40
60
80
100
120
TEMPERATURE (C)
TEMPERATURE (C)
Figure 13. Dropout Voltage vs. Temperature (Over Current Range)
6.0 5.5 5.0 OUTPUT VOLTAGE (V) 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 0 1.0 2.0 3.0 4.0 5.0 6.0 INPUT VOLTAGE (V) 1.5 V 800 ENABLE THRESHOLD (mV) Iout = 0 mA Cout = 1.0 mF TA = 25C ENABLE = Vin 3.0 V 5.0 V
Figure 14. Dropout Voltage vs. Temperature (Over Output Voltage)
750 Enable Increasing 700 Enable Decreasing 650 Vin = 5.5 V 600 -40 -15 10 35 60 85 110 125
3.3 V 2.80 V 1.80 V 1.25 V
TEMPERATURE (C)
Figure 15. Output Voltage vs. Input Voltage
Figure 16. Enable Threshold vs. Temperature
http://onsemi.com
7
NCP600
TYPICAL CHARACTERISTICS
6.0 154 GROUND CURRENT (mA) GROUND CURRENT (mA) 5.0 4.0 3.0 2.0 ENABLE = 0 V 1.0 0 -40 146 Vout = 1.25 V 138 130 122 114 106 98 -15 10 35 60 85 110 125 90 -40 -20 ENABLE = 0.9 V 0 20 40 60 80 100 120 Vout = 5.0 V Iout = 1.0 mA Iout = 150 mA Iout = 1.0 mA Iout = 150 mA
TEMPERATURE (C)
TEMPERATURE (C)
Figure 17. Ground Current (Sleep Mode) vs. Temperature
160 140 GROUND CURRENT (mA) 1.5 V 120 1.8 V 100 80 60 40 20 0 0 1.0 2.0 3.0 4.0 5.0 6.0 Vin, INPUT VOLTAGE (V) 1.25 V 2.8 V 3.0 V 105 3.3 V GROUND CURRENT (mA) 5.0 V 104 103 102 101 100 99 98 0 106
Figure 18. Ground Current (Run Mode) vs. Temperature
Vout = ADJ Vin = 1.75 V 25 50 75 100 125 150
OUTPUT CURRENT (mA)
Figure 19. Ground Current vs. Input Voltage
400 ADJ INPUT BIAS CURRENT (nA)
Figure 20. Ground Current vs. Output Current
300
200
100
0 -40
-20
0
20
40
60
80
100
120
TEMPERATURE (C)
Figure 21. ADJ Input Bias Current vs. Temperature
http://onsemi.com
8
NCP600
TYPICAL CHARACTERISTICS
OUTPUT SHORT CIRCUIT CURRENT (mA)
650
700 600
600
CURRENT LIMIT (mA) 0 20 40 60 80 100 120
500 400 300 200 100
550
500
450 -40 -20
0 0 1.0 2.0 3.0 4.0 5.0 6.0 TEMPERATURE (C) Vin, INPUT VOLTAGE (V)
Figure 22. Output Short Circuit Current vs. Temperature
4.0 LOAD REGULATION (mV) 5.0
Figure 23. Current Limit vs. Input Voltage
LINE REGULATION (mV)
3.0
4.0
3.0
2.0
2.0
1.0 Vin = (Vout + 0.5 V) to 6.0 V Iout = 1.0 mA 0 -40 -20 0 20 40 60 80 100 120
1.0 Iout = 1.0 mA to 150 mA 0 -40 -15 10 35 60 85 110 125
TEMPERATURE (C)
TEMPERATURE (C)
Figure 24. Line Regulation vs. Temperature
45 OUTPUT TURN ON TIME (mS) 40 35 5.0 V 30 25 3.0 V 20 15 1.5 V 1.25 V (ADJ) POWER SUPPLY RIPPLE REJECTION (dB) 80 70 60
Figure 25. Load Regulation vs. Temperature
1.25 V
3.3 V 50 40 30 20 10 0 Vin = Vout + 1.0 V Vripple = 0.5 Vp-p Cout = 1.0 mF Iout = 1.0 mA to 150 mA 0.1 1.0 10 100 5.0 V
10 -40 -20
0
20
40
60
80
100
120
TEMPERATURE (C)
FREQUENCY (kHz)
Figure 26. Output Turn On Time vs. Temperature
Figure 27. Power Supply Ripple Rejection vs. Frequency
http://onsemi.com
9
NCP600
TYPICAL CHARACTERISTICS
10 OUTPUT CAPACITOR ESR (W)
Vout = 5.0 V Vout = 1.25 V
Unstable Region
1.0 Stable Region 0.1 Cout = 1.0 mF to 10 mF TA = -40C to 125C Vin = up to 6.0 V 0 25 50 75 100 125 150
0.01
OUTPUT CURRENT (mA)
Figure 28. Output Stability with Output Capacitor ESR over Output Current
Vout = 1.25 V
Figure 29. Load Transient Response (1.0 mF)
Vout = 1.25 V
Figure 30. Load Transient Response (10 mF)
http://onsemi.com
10
NCP600
DEFINITIONS
Load Regulation Line Regulation
The change in output voltage for a change in output load current at a constant temperature.
Dropout Voltage
The input/output differential at which the regulator output no longer maintains regulation against further reductions in input voltage. Measured when the output drops 2% below its nominal. The junction temperature, load current, and minimum input supply requirements affect the dropout level.
Output Noise Voltage
The change in output voltage for a change in input voltage. The measurement is made under conditions of low dissipation or by using pulse techniques such that the average junction temperature is not significantly affected.
Line Transient Response
Typical output voltage overshoot and undershoot response when the input voltage is excited with a given slope.
Load Transient Response
This is the integrated value of the output noise over a specified frequency range. Input voltage and output load current are kept constant during the measurement. Results are expressed in mVrms or nV Hz.
Ground Current
Typical output voltage overshoot and undershoot response when the output current is excited with a given slope between no-load and full-load conditions.
Thermal Protection
Ground Current is the current that flows through the ground pin when the regulator operates without a load on its output (IGND). This consists of internal IC operation, bias, etc. It is actually the difference between the input current (measured through the LDO input pin) and the output load current. If the regulator has an input pin that reduces its internal bias and shuts off the output (enable/disable function), this term is called the standby current (ISTBY.)
Internal thermal shutdown circuitry is provided to protect the integrated circuit in the event that the maximum junction temperature is exceeded. When activated at typically 175C, the regulator turns off. This feature is provided to prevent failures from accidental overheating.
Maximum Package Power Dissipation
The power dissipation level at which the junction temperature reaches its maximum operating value.
APPLICATIONS INFORMATION The NCP600 series regulator is self-protected with internal thermal shutdown and internal current limit. Typical application circuits are shown in Figures 2 and 3.
Input Decoupling (Cin)
A ceramic or tantalum 1.0 mF capacitor is recommended and should be connected close to the NCP600 package. Higher capacitance and lower ESR will improve the overall line transient response.
Output Decoupling (Cout)
The NCP600 is a stable component and does not require a minimum Equivalent Series Resistance (ESR) for the output capacitor. The minimum output decoupling value is 1.0 mF and can be augmented to fulfill stringent load transient requirements. The regulator works with ceramic chip capacitors as well as tantalum devices. Larger values improve noise rejection and load regulation transient response. Figure [TBD] shows the stability region for a range of operating conditions and ESR values.
No-Load Regulation Considerations
The NCP600 adjustable regulator will operate properly under conditions where the only load current is through the resistor divider that sets the output voltage. However, in the case where the NCP600 is configured to provide a 1.250 V
output, there is no resistor divider. If the part is enabled under no-load conditions, leakage current through the pass transistor at junction temperatures above 85C can approach several microamperes, especially as junction temperature approaches 150C. If this leakage current is not directed into a load, the output voltage will rise up to a level approximately 20 mV above nominal. The NCP600 contains an overshoot clamp circuit to improve transient response during a load current step release. When output voltage exceeds the nominal by approximately 20 mV, this circuit becomes active and clamps the output from further voltage increase. Tying the ENABLE pin to Vin will ensure that the part is active whenever the supply voltage is present, thus guaranteeing that the clamp circuit is active whenever leakage current is present. When the NCP600 adjustable regulator is disabled, the overshoot clamp circuit becomes inactive and the pass transistor leakage will charge any capacitance on Vout. If no load is present, the output can charge up to within a few millivolts of Vin. In most applications, the load will present some impedance to Vout such that the output voltage will be inherently clamped at a safe level. A minimum load of 10 mA is recommended.
http://onsemi.com
11
NCP600
Noise Decoupling
The NCP600 is a low noise regulator and needs no external noise reduction capacitor. Unlike other low noise regulators which require an external capacitor and have slow startup times, the NCP600 operates without a noise reduction capacitor, has a typical 15 ms start up delay and achieves a 50 mVrms overall noise level between 10 Hz and 100 kHz.
Enable Operation
power dissipation supported by the device is dependent upon board design and layout. Mounting pad configuration on the PCB, the board material, and the ambient temperature affect the rate of junction temperature rise for the part. When the NCP600 has good thermal conductivity through the PCB, the junction temperature will be relatively low with high power applications. The maximum dissipation the NCP600 can handle is given by:
PD(MAX) + TJ(MAX) * TA RqJA (eq. 3)
The enable pin will turn the regulator on or off. The threshold limits are covered in the electrical characteristics table in this data sheet. The turn-on/turn-off transient voltage being supplied to the enable pin should exceed a slew rate of 10 mV/ms to ensure correct operation. If the enable function is not to be used then the pin should be connected to Vin.
Output Voltage Adjust
Since TJ is not recommended to exceed 125_C (TJ(MAX)), then the NCP600 can dissipate up to 400 mW when the ambient temperature (TA) is 25_C. The power dissipated by the NCP600 can be calculated from the following equations:
PD [ VIN(IGND@IOUT) ) IOUT(VIN * VOUT) (eq. 4)
The output voltage can be adjusted from 1 times (Figure 2) to 4 times (Figure 3) the typical 1.250 V regulation voltage via the use of resistors between the output and the ADJ input. The output voltage and resistors are chosen using Equation 1 and Equation 2.
VOUT + 1.250 1 ) R1 ) (IADJ R2 R1 + R2 * R2) (eq. 1)
or
VIN(MAX) [ PD(MAX) ) (VOUT IOUT) IOUT ) IGND
(eq. 5)
[Vout * (IADJ * R2)] V * 1 ^ R2 out * 1 1.25 1.25 (eq. 2)
If a 150 mA output current is needed, the quiescent current IGND is taken from the data sheet electrical characteristics table or extracted from Figure TBD and Figure TBD. IGND is approximately 108 mA when Iout = 150 mA. For an output voltage of 1.250 V, the maximum input voltage will then be 3.9 V, good for a 1 Cell Li-ion battery.
Hints
Input bias current IADJ is typically less than 150 nA. Choose R2 arbitrarily t minimize errors due to the bias current and to minimize noise contribution to the output voltage. Use Equation 2 to find the required value for R1.
Thermal
As power in the NCP600 increases, it might become necessary to provide some thermal relief. The maximum
DEVICE ORDERING INFORMATION
Device NCP600SNADJT1G NCP600SN150T1G NCP600SN180T1G NCP600SN280T1G NCP600SN300T1G NCP600SN330T1G NCP600SN500T1G Marking Code LIO LID LIE LIH LIJ LIK LIN
Vin and GND printed circuit board traces should be as wide as possible. When the impedance of these traces is high, there is a chance to pick up noise or cause the regulator to malfunction. Place external components, especially the output capacitor, as close as possible to the NCP600, and make traces as short as possible.
Version ADJ 1.5 V 1.8 V 2.8 V 3.0 V 3.3 V 5.0 V
Package
Shipping*
TSOP-5 (Pb-Free)
3000/Tape & Reel
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
12
NCP600
PACKAGE DIMENSIONS
TSOP-5 CASE 483-02 ISSUE F
NOTE 5 2X
D 5X 0.20 C A B
5 1 2 4 3
0.10 T 0.20 T L G A B S
M K
DETAIL Z
2X
NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. 5. OPTIONAL CONSTRUCTION: AN ADDITIONAL TRIMMED LEAD IS ALLOWED IN THIS LOCATION. TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2 FROM BODY. DIM A B C D G H J K L M S MILLIMETERS MIN MAX 3.00 BSC 1.50 BSC 0.90 1.10 0.25 0.50 0.95 BSC 0.01 0.10 0.10 0.26 0.20 0.60 1.25 1.55 0_ 10 _ 2.50 3.00
DETAIL Z
J C 0.05 H T
SEATING PLANE
SOLDERING FOOTPRINT*
1.9 0.074
0.95 0.037
2.4 0.094 1.0 0.039 0.7 0.028
SCALE 10:1
mm inches
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative
http://onsemi.com
13
NCP600/D

▲Up To Search▲

Price & Availability of NCP600SN180T1G

	To Download NCP600SN180T1G Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .